Why Understanding Essential Plumbing Skills is Important When Installing a Bathtub
Why Understanding Essential Plumbing Skills is Important When Installing a Bathtub
Blog Article
Right here down the page you can discover some reliable data concerning How to Install a Bathtub Yourself.
Setting up a tub isn't exactly brain surgery, however it does call for solid plumbing, woodworking, and sometimes, tiling skills. Changing an old tub with a new one is additionally a moderately tough job. If the old tub is easily accessible, the project can relocate rapidly; if you need to open up a wall to remove the old bathtub and also position the new tub, the task is much harder. In either case, the project is within a residence handyman's skills, although you will need a helper to vacate the old bathtub as well as embeded in the brand-new one. See to it you have qualified yourself for the job and also are comfortable trying it. Instead of hiring a specialist to take control of a halfway-completed task, it is better to take into consideration using one before you start. Chances are you may need a professional plumber to make tube connections.
This write-up will certainly help you mount a new bath tub in your bathroom if you have actually currently acquired a new bathtub and also do not require to alter the plan of your previous water pipelines.
Your tools as well as material list must consist of the following:
Planning for the Installation
Firstly, the sustaining frame supplied with the bath must be fitted (if required) according to the supplier's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to make certain that if the tap comes with a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you utilize every one of the provided washers.
Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be fitted in its final setting.
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, then the first thing you must do is separate the water supply. After doing so, activate the faucets to drain any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly problematic due to the limited access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the faucets. Have a cloth ready for the staying water that will originate from the pipelines. When the supply pipes have been removed, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from transforming throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing compound.
Prior to proceeding to fit the new faucets, compare the pipeline links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Mounting the Tub
Making use of both wooden boards under its feet, position the tub in the called for setting. The wooden boards are useful in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 small points.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and readjusting the feet on the tub till the level reads degree.
To mount faucets, fit the bottom of the outermost versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Switch on the supply of water as well as inspect all joints and also brand-new pipework for leakages and also tighten them if required. Fill the tub and additionally check the overflow outlet and also the typical electrical outlet for leaks.
Finally, take care of the bath paneling as defined in the manufacturer's user's manual. Tiling and also securing around the tub ought to wait up until the tub has been utilized at least once as this will resolve it right into its last position.
Fitting New Taps
If the tails of the new taps are plastic, after that you will require a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end provides a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin guaranteeing that the washing machines remain in location between the tap and the sink. Safeguard the tap in place with the producer provided backnut. When the faucet is safely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former type should be attached to the tap ends initially, tightening up only by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bathroom satisfies the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a stiff seal, creating the water to penetrate the wall in between the bathroom as well as the tiling, resulting in difficulties with wetness and possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components as well as installations. They are marketed in tubes and cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the bath tub with water before sealing, to permit the motion experienced when the tub remains in use. The sealant can break fairly early if you do not take into account this movement prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that editorial about How to Install a Bathtub through a good friend on a different domain. Sharing is good. Helping others is fun. Many thanks for your time. Please visit our site back soon.
No more waits, dial now! Report this page